Separate Amplifier Model, Amplifier Units Main unit (M8 Connector Type) LR-XN11C

LR-XN11C - Separate Amplifier Model, Amplifier Units Main unit (M8 Connector Type)

Data Sheet (PDF)

Manuals

Specifications

Model		LR-XN11C
Type		NPN Output/PNP Output (Selectable output)
Cable/Connector		M8 connector^*1
Main Unit/Expansion Unit		Main Unit (expansion not possible)
No. of Control Outputs		2^*2
No. of External Inputs		1^*2
Response Time		500 µs^*3/1 ms/3 ms/10 ms/200 ms Selectable
IO-Link		Specification v1.1/COM2 (38.4 kbps)
Functions	Timer Function	Timer OFF/Off-delay/On-delay/One-shot/On-Off delay/On-delay One-shot
I/O	Control Output	Open collector, 30 VDC or lower, N.O./N.C. 100 mA or lower for 1 output; 100 mA or lower in total for 2 outputs Residual voltage NPN: 1.4 V or lower (output current: 10 mA or lower)/2 V or lower (output current: 10 to 100 mA), PNP: 1.6 V or lower (output current: 10 mA or lower)/2.2 V or lower (output current: 10 to 100 mA)
	External Input	External Set/Laser OFF/Zero Shift/Hold Reset/Gyro Alert RST selectable Short circuit current - NPN: 1 mA or lower, PNP: 2 mA or lower Input time: 3 ms or more ON, 20 ms or more OFF (25 ms or more ON, 25 ms or more OFF only when External Set is selected)
Unit Expansion		—
Protection Circuit		Protection against reverse power connection, protection against output overcurrent, protection against output surge, protection against reverse output connection
Number of Interference Prevention Devices		—
Power supply	Power voltage	16 to 30 VDC^*4 (including 10% ripple (P-P) or less), class 2
	Power consumption	During normal operation: 1150 mW (47 mA or lower at 24 V, 64 mA or lower at 16 V), ECO ON/ALL: 985 mW (40 mA or lower at 24 V, 53 mA or lower at 16 V) (excluding Load Current)
Environmental resistance	Ambient temperature	−20 to +55°C -4°F to 131°F (no freezing)^*5
	Relative humidity	35 to 85% RH (no condensation)
	Vibration resistance	10 to 500 Hz; Power Spectral Density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	500 m/s² (50G); 3 times each for X, Y, and Z axes
Case Material		Main Unit and Cover: Polycarbonate
Accessories		Instruction manual
Weight		Approx. 22 g
^1 Ensure the cable length is 30 m 98.4' or less for the M8 connector type. Ensure the cable length is 20 m 65.6' or less when connecting via IO-Link. ^2 Output 2 and the external input are selectable. ^3 If 500 µs is selected, the following limitations apply. · Only 2-point calibration can be performed. · The detection range masking is set during calibration. (Manual setting of the masking range is not supported.) · Output 2 is limited to an alarm output for errors and gyro issues, and standard/area cannot be used. · The interference prevention function is not supported ^4 When expanding the system with 4 or more expansion units, use a power voltage of 20 V or higher. ^*5 Expansion by 1 or 2 units: −20 to +55°C -4°F to 131°F; Expansion by 3 to 10 units: -20 to +50°C -4°F to 122°F, Expansion by 11 to 16 units: -20 to +45°C -4°F to 113°F

Other Models